Page 1 of 1

How to Clean a Metal Strainer

Posted: May 16th, '10, 03:59
by chittychat
Make sure enough deposit has accumulated. Make sure it is very dry. Then use a small brass brush to brush-off the gum. And it will become like new, well almost. :)

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 10:46
by Chip
Yeah, I let it fully dry too, but I have been using a toothbrush.

I also use a tiny bottle brush to go down the spout and clean out the gunkage. :mrgreen:

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 13:36
by IPT
Chip wrote:I also use a tiny bottle brush to go down the spout and clean out the gunkage. :mrgreen:
I use bottle brushes too. I keep stealing my daughter's and have to buy new ones. :oops:

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 13:54
by Chip
IPT wrote:
Chip wrote:I also use a tiny bottle brush to go down the spout and clean out the gunkage. :mrgreen:
I use bottle brushes too. I keep stealing my daughter's and have to buy new ones. :oops:
Ya gotta clean your spouts ... you never know what you may find in there. I once found a family of TeaChat trolls I had banned trying to sabotage my kyusu-s. :lol:

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 14:00
by Rithmomachy
Chip wrote:Ya gotta clean your spouts ... you never know what you may find in there.
Good advice in all areas of life! :mrgreen:

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 15:43
by rabbit
I rub the wet leaves thru the grate with my fingers while running water over it, that usually works, of course if it doesn't I let it dry (but we don't always have enough time between teas!!!)

Re: How to Clean a Metal Strainer

Posted: May 18th, '10, 23:53
by chittychat
Chip wrote:Yeah, I let it fully dry too, but I have been using a toothbrush.

I also use a tiny bottle brush to go down the spout and clean out the gunkage. :mrgreen:
Pipe cleaners are good for cleaning the spout. Look for the ones with stiffer bristles.

Re: How to Clean a Metal Strainer

Posted: May 19th, '10, 02:58
by IPT
Chip wrote:Yeah, I let it fully dry too, but I have been using a toothbrush.

I also use a tiny bottle brush to go down the spout and clean out the gunkage. :mrgreen:

Darn that gunkage! :x

Re: How to Clean a Metal Strainer

Posted: May 19th, '10, 12:23
by nonc_ron
IPT wrote:Darn that gunkage! :x
Ditto! on that darn gunkage.
The more I try to ignore it the more it tries to take over. :roll:

On how to clean a Metal Strainer, I let it dry, then whack it on the side of the sink.Image

Re: How to Clean a Metal Strainer

Posted: May 30th, '10, 00:02
by chittychat
And now how to make it sparkling clean :!: :D

The attached pictures shows the top of the strainer not cleaned and the bottom sparkling.

I guess you want to know how :roll:

Here I spill the secret: boil it briefly in vinegar. :mrgreen:
Then clean with a toothbrash and laundry soap. The vinegar can be reused for another clean boiling. Use the cheap kind not that Italian balsamic one. :wink:

Re: How to Clean a Metal Strainer

Posted: May 30th, '10, 23:06
by nonc_ron
chittychat wrote:And now how to make it sparkling clean :!: :D
Here I spill the secret: boil it briefly in vinegar. :mrgreen:
Wow, I'd forgotten how mine use to look like.
Thanks for the boiling vinegar trick. I'll try it tomorrow when I can open all the windows and doors. :D

Re: How to Clean a Metal Strainer

Posted: Jun 5th, '10, 19:37
by mbishop
I took out the metal band from my kyusu, let it try, rubbed it a little, then soaked it in water (and kind of "plunged" it up and down), removed quite a bit of the little particles. I didn't have a brush handy (that was clean) so I took a straight pin and just popped out the somewhat larger pieces with the point :P